Tag Archives: crystal oscillators

The BitX 20 & More

The BitX

20160618_120709I was fortunate to recently have been gifted a BitX 20 kit by a friend and fellow VE. The kit came from QRPkits.com some time ago, I believe at least a year or so ago.

My intention was to build it for Field Day 2016. Sadly, while I was well on track to getting the radio built, 2 parts were missing from the kit. BS170 N-Channel MOSFETs to be specific. This put on the breaks for the final assembly and stopped me dead in my tracks with the finish line in sight.

20160624_193754I have the parts waiting for me at Jameco will-call for Monday. Once I get them home, populating the remainder of the circuit board should take about an hour. Then its on to the initial tuning and getting the radio packaged up in its housing.

I will do a full project write-up in the Projects section soon, but for now just an update.

A Homebrew Signal Generator/Oscillator

20160622_084953During the BitX build I ran into a small hiccough. The testing at some point calls for the injection of an 11 MHz signal. I would normally use my Lafayette signal generator but for some reason it’s on the fritz so I had to come up with another solution… build an 11 MHz signal generator.

20160622_085219With the crystals in the kit it was easy to build a simple generator with parts on hand and while I only had 1 of the five crystals installed it was easy. By the next testing phase I had installed the remaining 4 crystals. Now I need one for the homebrew SigGen! (click the image for the circuit diagram)

Off to HSC Electronic Supply for some 11 MHz crystals.

This project will also get a write-up in the Projects section soon. This one in in particular has a lot of use in checking unmarked crystals as long as they are between 1 and 20 MHz and is a great foundation piece for beginning builders.

A Homebrew TNC

20160524_145401Before I got started on the BitX I was working on getting my Baofeng 2m/70cm HT on digital. I found a couple of designs for a homebrew TNC and set out to make that work.

Because of the way the PTT key works on the Baofeng I haven’t been able to make the TNC work with the HT but it should work fine with my 40 meter QRPme.com Splinter II and the BitX 20.

A full write-up post is coming on this one too.

Look for all three of these in the Projects section for full details on the builds coming soon.

It’s been a long time since I posted, and most of that time I have been working on non-radio stuff. Now that I am back in the swing of things I have more time for radio stuff so I should be able to post more, and make updates to the Projects pages

As soon as the BitX 20 is up and running I plan on getting the Lafayette working again and get back to the Beach 40 DSB. Another Field Day has slipped through my fingers. I don’t plan on that happening again!

That’s all for now folks, 72, 73, and good night!

~Jon KK6GXG

 

Work On The Beach 40 Begins

Back to building! I finalized the drawings for my implementation of VK3YE’s Beach 40 DSB Transceiver. I created a project page for it here.  I also finished the the “final” version of the diagram, at least until I get the physical build under way. I will be updating the diagram on the project page but not here so if you are interested in this project, check out the build page.

VK3YE-Beach-40-KK6GXG
Here is the full diagram I completed today. Click for full size image

While I am heating up the soldering iron tonight, another important part of this project is the documentation. Not only am I going to be updating the project page as the build progresses I will also be keeping a lab journal.

This is something new for me. I have never been skilled at keeping lab notes. This is something I need to work on now that I am getting more involved in RF electronics as an experimenter.

That’s it for now. More to come.

73,
~Jon KK6GXG